- Black anodized finish with insulated hand grips. Crimp slot on end of tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire.Works with 10 to 22 guage solderless terminals. Great tool for crimping the ends on Dyna spark plug wires WARNING: Disconnect power source before using this tool! Keyword: Crimper

$12.00 Ea

- OEM: DC10-1 5 ohm 12-volt black coils. Replacement for factory coils. Fatter spark means smoother running and less chance of fouling a plug.
See below for plug wires.
Check the resistance of the coils you are replacing to ensure a correct match.
If you have questions if these are correct, please call us or Dynatek at 1-800-928-3962
Never select a coil with a lower resistance than your ignition system - this will cause the coils to overheat and burn out... It is OK to select coi

$67.00 Ea

- OEM: DC3-1 DYDC3-1. 3 ohm green coils. Replacement for factory coils. Matched to the Dyna-S Electronic Ignitions. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils work to replace some point system coils where the resistance is in the low to mid 3 ohm range. For some Kawasaki bikes with a resistor in the circuit (i.e. KZ1000's in the late 70's and early 80

$130.00 Ea

- DC3-2 (used with twin cylinder bikes fitted with two single output coil) 3 ohm mini black coil. Smaller and lighter than the DC3-1 coils, these are ideal for drag racing applications. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. For some Kawasaki bikes with a ballast resistor in the circuit, the 3 ohm coil is the best choice - just remove the ballast resistor from t

$137.00 Ea

- DC3-2 (used with twin cylinder bikes fitted with one single output coil) 3 ohm mini black coil. Smaller and lighter than the DC3-1 coils, these are ideal for drag racing applications. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. For some Kawasaki bikes with a ballast resistor in the circuit, the 3 ohm coil is the best choice - just remove the ballast resistor from t

$70.50 Ea

- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.

$51.00 Ea

- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.

$51.00 Ea

- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.

$51.00 Ea

- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.

$51.00 Ea

- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.

$51.00 Ea

- Headlight Bulb - Halogen H4 55/60W

$3.53 Ea

- Headlight Bulb - Halogen H4 90/100W PLEASE NOTE - make sure your bikes charging system and wiring harness is capable of supporting these high output bulbs. On many bikes these bulbs will drain the battery if the headlight is run constantly.

$3.53 Ea

- Headlight Bulb - Halogen H4 55/100W PLEASE NOTE - make sure your bikes charging system and wiring harness is capable of supporting these high output bulbs. On most bikes the 100w high beam should only be used for VERY brief periods to avoid draining the battery

$5.88 Ea

- Equivalent to OEM: 38310-415-671 12V Replacement for Honda Part 38310-415-671 (2 prong). 23w x 2, plus 3.4w or 21x x 2, plus 4w. These are the wattages of the turn signal bulbs plus the instrument panel bulb. These do not work for LED turn signals. Keyword: Relay

$7.81 Ea

- 12-volt 3.0 amp horn with 90mm mount bracket with pre-drilled hole. Direct replacement for Z1 / KZ900 horns - includes wiring to hook up - louder than stock horn. 110db

$33.20 Ea

- 12-volt 2.5 amp horn with 90mm mount bracket with pre-drilled hole. Includes two crimp on connectors. 105db

$23.60 Ea

- B-13R - 6 Pin White Terminal Connector Set with Retainer - 10 Pack - Used with - B9 and - B10 (SEE BELOW)

$20.70 Ea

- B-13R- 6 Pin White Terminal Connector Set with Retainer - Individual - Used with - B9 and - B10 (SEE BELOW)

$2.40 Ea

- B18R - 4 Pin White Terminal Connector Set with Retainer - 10 Pack - Used with - B9 and - B10 (SEE BELOW)

$15.20 Ea

- B18R 4 Pin White Terminal Connector Set with Retainer - Individual - Used with - B9 and - B10 (SEE BELOW)

$1.80 Ea