|
DYCT-1 - Dyna Spark Plug Wire Crimping Tool
- Black anodized finish with insulated hand grips. Crimp slot on end of tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire.Works with 10 to 22 guage solderless terminals. Great tool for crimping the ends on Dyna spark plug wires WARNING: Disconnect power source before using this tool! Keyword: Crimper
|
$12.00 Ea
|
|
DYDC1-1 - Dyna Dual Output 3.0 Ohm Coils (pair) DC1-1
- OEM: DC1-1 - DYDC1-1. 3 ohm green coils. OEM: DC10-1 5 ohm 12-volt black coils. Replacement for factory coils. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. If you have questions if these are correct, please call us or Dynatek at 1-800-928-3962 Never select a coil with a lower resistance than your ignition system - this will cause the coils to overh
|
$130.00 Ea
|
|
DYDC1-2 - Dyna Dual Output 3.0 Ohm Mini Coils (pair) DC1-2
- 3 ohm mini black coils. Smaller and lighter than the DC1-1 coils, these are ideal for drag racing applications. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils are designed for use with the Dyna 2000 and 3000 series ignitions, factory installed electronics, or other after-market ignitions that employ dwell control They should not be used with the Dyna-S i
|
$137.00 Ea
|
|
DYDC2-1 - Dyna Dual Output Coil 1.5 Ohm (pair) DC2-1
- OEM: DC2-1- 1.5 ohm red coils. Replacement for ignition systems requiring 1.5 ohm coils. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils work to replace some CDI or electronic ignition system coils where the resistance is in the 1.5 ohm - 2 ohm range. DO NOT USE these with DYNA S or DYNA 2000 ignitions. If you have questions if these are correct, please ca
|
$130.00 Ea
|
|
DYDC3-1 - Dyna Single Output 3.0 Ohm Coils (pair) DC3-1
- OEM: DC3-1 DYDC3-1. 3 ohm green coils. Replacement for factory coils. Matched to the Dyna-S Electronic Ignitions. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils work to replace some point system coils where the resistance is in the low to mid 3 ohm range. For some Kawasaki bikes with a resistor in the circuit (i.e. KZ1000's in the late 70's and early 80
|
$130.00 Ea
|
|
DYDC3-2 - Dyna Single Output 3.0 Ohm Mini Coils (Pair) DC3-2
- DC3-2 (used with twin cylinder bikes fitted with two single output coil) 3 ohm mini black coil. Smaller and lighter than the DC3-1 coils, these are ideal for drag racing applications. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. For some Kawasaki bikes with a ballast resistor in the circuit, the 3 ohm coil is the best choice - just remove the ballast resistor from t
|
$137.00 Ea
|
|
DYDC3-2-Single - Dyna Single Output 3.0 Ohm Mini Coil (1) DC3-2
- DC3-2 (used with twin cylinder bikes fitted with one single output coil) 3 ohm mini black coil. Smaller and lighter than the DC3-1 coils, these are ideal for drag racing applications. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. For some Kawasaki bikes with a ballast resistor in the circuit, the 3 ohm coil is the best choice - just remove the ballast resistor from t
|
$70.50 Ea
|
|
DYDC4-1 - Dyna Dual Output 2.2 Ohm Coils (pair) DC4-1
- OEM: DC4-1- 2.2 ohm grey coils. Replacement for factory coils. Matched to the Dyna 2000 Electronic Ignitions. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils work to replace some CDI or electronic ignition system coils where the resistance is in the low to mid 2 ohm range. If you have questions if these are correct, please call us or Dynatek at 1-800-928
|
$130.00 Ea
|
|
DYDC8-1 - Dyna Dual Output 5.0 Ohm Coils (pair) DC8-1
- OEM: DC8-1 - 5.0 ohm black coils. Replacement for factory coils. Matched to many factory points systems. Fatter spark means smoother running and less chance of fouling a plug. See below for plug wires. Check the resistance of the coils you are replacing to ensure a correct match. These coils work to replace some CDI or electronic ignition system coils where the resistance is around the 5.0 ohm range. If you have questions if these are correct, please call us or Dynatek at 1-800-928-3962 Nev
|
$130.00 Ea
|
|
DYDSL-2-Black - Dyna Mini Shift Light Black
- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.
|
$51.00 Ea
|
|
DYDSL-2-BLUE - Dyna Mini Shift Light Blue
- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.
|
$51.00 Ea
|
|
DYDSL-2-GREEN - Dyna Mini Shift Light Green
- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.
|
$51.00 Ea
|
|
DYDSL-2-RED - Dyna Mini Shift Light Red
- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.
|
$51.00 Ea
|
|
DYDSL-2-Silver - Dyna Mini Shift Light Silver
- Dyna Mini Shift Light is used in conjunction with Dyna Shift Minder System.
|
$51.00 Ea
|
|
DYDW200 - Dyna Ignition Wires 7mm copper core (black)
- OEM: DW200- BLACK 7mm copper core - set of 4 wires with plug caps, rubber boots and connectors Supplied as two wires with plug caps on either end. Cut the wires in half and trim to size required. Dynatek "Dyna" Wires are available with a stranded copper core for use on older vehicles where electrical interference is not an issue. For use on new vehicles with electronic advance ignitions or other sensitive electronic equipment use DYNA suppression core wires. Both wire types ensure maximum en
|
$17.00 Ea
|
|
DYDW300 - Dyna Ignition Wires 7mm copper core (red)
- OEM: DW300- RED 7mm copper core - set of 4 wires with plug caps, rubber boots and connectors Supplied as two wires with plug caps on either end. Cut the wires in half and trim to size required. Dynatek "Dyna" Wires are available with a stranded copper core for use on older vehicles where electrical interference is not an issue. For use on new vehicles with electronic advance ignitions or other sensitive electronic equipment use DYNA suppression core wires. Both wire types ensure maximum ener
|
$17.00 Ea
|
|
DYDW500 - Dyna Ignition Wires 7mm suppression (yellow)
- OEM: DW500 - LIMITED AVAILABILITY Dynatek phased these wires out two years ago - but in clearing out a stock room, Dynatek discovered a small number of these wires - when they are gone, they are gone... YELLOW 7mm suppresion wires - set of 4 wires with plug caps, rubber boots and connectors Supplied as two wires with plug caps on either end. Cut the wires in half and trim to size required. Dynatek "Dyna" Wires are available with a solid copper core for use on older vehicles where electrical
|
$17.00 Ea
|
|
DYDW600 - Dyna Ignition Wires 7mm Suppression Core (Black)
- Black 7mm Suppression core wires with plug caps, rubber boots and connectors Supplied as two wires with plug caps on either end. Cut the wires in half and trim to size required. Dynatek "Dyna" Wires are available with a solid copper core for use on older vehicles where electrical interference is not an issue. For use on new vehicles with electronic advance ignitions or other sensitive electronic equipment use DYNA suppression wires with a high grade graphite core for best performance and electri
|
$17.00 Ea
|
|
DYDW800 - Dyna Ignition Wires 8mm suppression core (grey)
- OEM: DW800 - GREY 8mm suppression core - set of 4 wires with plug caps, rubber boots and connectors Supplied as two wires with plug caps on either end. Cut the wires in half and trim to size required. Dynatek "Dyna" Wires are available with a solid copper core for use on older vehicles where electrical interference is not an issue. For use on new vehicles with electronic advance ignitions or other sensitive electronic equipment use DYNA suppression wires with a high grade graphite core for be
|
$17.00 Ea
|
|
KL35-6894 - Timing/Work Light Self Powered
- Timing/Work Light Self Powered - Combines timing light and work light into one instrument. Works on all 12-volt gasoline powered engines. Uses 2 "D" cell batteries. Includes an LED indicator to insure proper hook up or detects a faulty flash tube.
|
$83.10 Ea
|