Featured Products // Carburetors

Kawasaki Mikuni RS34 carburetors z1enterprises

Happy New Year!

Looking back on 2017,  you probably put a healthy number of miles on your Z1 or you finally scored a CB750 after hours of scrolling through Craigslist. In both cases, a carb cleaning/rebuild may be in your near future.

  • Is your motorcycle hard to start?
  • Is it running a bit off-kilter?
  • When you dial the throttle, are you getting the desired performance?
  • Do you ride with the choke on? ( this means you have a clogged pilot jet )
  • Sluggish acceleration?
  • Bad fuel economy?

These are all signs that your bike is in need of some carburetor love. In most scenarios, there’s only really one way to see if your carbs are due for a complete rebuild: pull them off the bike and take a look inside. And since you have them off and dissembled, you might as well do your future self a favor and rebuild them now.

January’s Featured Products are dedicated to those precious carburetors, everything from the entire assembly to the needle and seat.


  Mikuni RS34 Carburetors

Kawasaki Mikuni RS34 carburetors z1enterprises

Designed for in-line 4 cylinder performance motorcycle applications, the Mikuni RS Series Radial Flat Slide Carburetors offer superior horsepower gains with their maximum flowing smoothbore induction tract and radial flat slide design. An adjustable accelerator pump system helps to provide instant throttle response, particularly in the lower RPM range. The RS Series Carburetors feature a compact design which is 25% lighter than other performance carburetors and uses readily available Mikuni jets.


 

Z1 Premium ‘Nencho’ Carb Rebuild Kit 

(1973-1974) 

200-1100 keyster premium nencho carb kit z1 1973-1974

These kits contain parts not normally available – and help solve rough running issues related to these Z1 carbs.

Included in the kit are:

  • 4 x different Jet Needles – Lean, Standard (5J9), Rich, Richer
  • Needle Jet
  • 4 x Needle Circlips
  • 6 x different main jets – 107, 108 112.5 (standard), 116, 120 & 125
  • 3 x different pilot jets – 19, 20, 26
  • Choke Plunger, Choke Plunger Spring, Choke Plunger o-ring
  • Emulsion Tube (main jet holder)
  • Drain Plug o-ring
  • Carb Top and Float Bowl Gasket
  • Float Needle Valve Assembly with fiber washer
  • Air Screw and Air Screw Spring

 

***Note: Four (4) kits are required to service a set of carbs.***

We have a wide selection of ‘Nencho’ kits and other carb rebuild kits for a variety of Kawasaki, Honda, Suzuki, and Yamaha models HERE.


 

Dynojet Carburetor Kit for Suzuki GS1100 

(1980-1986) 

Suzuki GS1100 Dynojet carb rebuild kit

Stage 1-3 Dynojet Carb Kit for the Suzuki 1980-86 GS1100 and GS1150 16-Valve.

Kit includes:

(4) #110 Main Jets

(4) #114 Main Jets

(4) #132 Main Jets

(4) #138 Main Jets

(4) Fuel Needles

(4) Adjusting Washers

(4) E-Clips

(4) Pilot Air Jets

(1) Slide Drill

(1) Plug Drill

(1) Screw

STAGE 1: Intended for motorcycles with a stock engine using the stock airbox- air filter and stock pipe. Stage 1 kits are fully adjustable to allow the use of a well designed aftermarket pipes and stock replacement air filters like K&N. Stage 1 kits are designed to improve throttle response and driveability and in most cases power increases of approximately 5% throughout the entire power range can be achieved.

STAGE 2: Intended for motorcycles with a stock or mildly tuned engine using a well designed aftermarket pipe with a modified airbox and a stock replacement air filter. Stage 2 kits are designed for applications where individual filters cannot be installed and for applications where airbox modification improves the engine’s performance. In most cases power increases of approximately 8% can be achieved.

STAGE 3: Intended for motorcycles with stock or mildly tuned engines using a well designed aftermarket pipe and individual air filters. In most cases power increases of 10-15% can be achieved.

 

Be sure to check out our nice selection of Suzuki parts HERE

 


Carburetor Screw Set 

NGSS 2002 Carb Screw Set

Stainless Steel bolt set to replace those easily damaged Phillips pan head carb top and float bowl screws.

Includes:

28 socket head bolts- 28 lock washers and 1 Allen key for a total of 57 pieces.

Kawasaki:
1980-82 KZ550A- 1980-1983 KZ550C- 1981 KZ550D- 1977-78 KZ650- 1976-77 KZ900- 1977-78 KZ1000

Suzuki:
1977-1979 GS750- 1979 GS850- 1978-79 GS1000

Fits Mikuni VM29 29mm smoothbore carbs


 

So, there you have it! Some highlights of our Featured Products of January, all about carbs! It’s a new year so give your vintage Japanese motorcycle new life with some carburetor TLC.

feel free to contact us at

customerservice@z1enterprises.com